Difference between revisions of "MEEP"
(→Amazon EC2 AMI)
(→Setup: Added note about cygwin)
|Line 3:||Line 3:|
= Setup =
= Setup =
== Linux setup ==
== Linux setup ==
=== Default installation ===
=== Default installation ===
Revision as of 07:19, 16 July 2015
Meep (or MEEP) is a free finite-difference time-domain  simulation software package developed at MIT to model electromagnetic systems. A number of people, including @aero, have been using it to simulate the evolution of the fields within the EM Drive.
- 1 Setup
- 2 Usage
- 3 Candidate parameters for sensitivity analysis
- 4 Candidate shapes for further analysis
- 5 Creating an animation from a set of images
- 6 Models & results
- 7 Runtime & performance
- 8 References
Details regarding setting up Meep for EM Drive simulations are provided below.
Most people are running MEEP on Ubuntu, although @lmbfan has also managed to set it up on Windows via Cygwin.
Ubuntu Linux setup
apt-get install meep h5utils
@leomillert recommended the following:
- Meep 1.3 (compiled & installed from its sources)
- libctl 3.2.2 (compiled & installed from its sources)
- Guile 2.0.11 (id)
- Harminv 1.4 (id)
- OpenBLAS 0.2.12 (installed from its binaries)
- HDF5 1.9.224 (compiled & installed from its sources)
- h5utils 1.12.1 (id)
Amazon EC2 AMI
Due to the long computing times required to simulate the frustum until "saturation" (for lack of a better term), you may find it more convenient to run the simulation on Amazon EC2 than on your machine.
An Amazon machine image (AMI) with Meep pre-installed has been made available by @dumbo. The AMI name is ubuntu-trusty-meep-emdrive and the AMI ID is ami-e5cbc9d5. The AMI is based on Ubuntu 14.04.2 (Trusty Tahr). Meep was installed from source using the following dependencies:
- Meep 1.3 (installed from source)
- libctl 3.2.2 (installed from source)
- Guile 2.0.9 (as provided by Ubuntu package guile-2.0)
- Harminv 1.4 (installed from source)
- OpenBLAS 0.2.14 (installed from source)
- HDF5 1.8.15 Patch 1 (installed from source)
- h5utils 1.12.1 (installed from source)
- GSL 1.16
TBD: the above sentence is unclear. If someone wants to use this AMI image, should it be run with or without mpi by preference ? If it is with mpi, why this additional step? Comment: I have updated the image, and this step is no longer required. The new image corrects a number of problems I have identified in running my tests, and should be used exclusively.
TBD: Describe here where to find a virtualbox pre-build image. This will allow everyone to run Meep in the same setup under Linux, Windows, Mac, Solaris, and also provides an opportunity to get *exactly* the same results (ie h5 files), which will simplify comparisons. The overhead of the VM is negligible compared to the benefits.
The instructions below were provided by @leomillert:
wget "https://forum.nasaspaceflight.com/index.php?action=dlattach;topic=37642.0;attach=1042821" -O NSF-1701.ctl meep NSF-1701.ctl
After completion of the execution, Meep outputs nine .h5 files (this may take a long time: see below).
2. Create CSV files
h5totxt -t 13 -0 -y -0 ex.h5 > zCopper-exy.csv
3. Open zCopper-exy.csv in a spreadsheet and aero's zCopper-exy.csv (TBD:provide location of aero csv) on another. Open a third spreadsheet that is one spreadsheet values minus the other, entry by entry. Check the highest entry (in absolute value) of the difference. If it's negligible you are good to go. If it's a value too big (greater than 10^-6), your Meep installation isn't in sync with ours, so it's of no use.
4. Now you are good to go. Make a new directory to start the tests. Copy NSF-1701.ctl there.
5. Open NSF-1701.ctl in a text editor and change a single value. For example, (set! high 10.2) means the model is 10.2 inches high. Change the 10.2 to another value and save NSF-1701.ctl with this single change. This is called sensitivity analysis. One value at a time. (set! high 10.2) was just an example, change any value of interest
meep NSF-1701.ctl h5totxt -t 13 -0 -y -0 ex.h5 > zCopper-exy.csv
6. Compare your new zCopper-exy.csv with your old one. See if there was any relevant change (do the spreadsheet comparison again). If there is no significant change in values, it means the modification made doesn't impact the behaviour of the EMDrive. This is an important information for scientists, so let us know. Otherwise, if there was a significant change, let us know if it was positive or negative and its intensity. If you don't know how, just upload the .h5 files somewhere and we will analyse it.
Candidate parameters for sensitivity analysis
The following change in parameters would benefit from sensitivity analysis.
- Property of the metallic material (for the moment copper)
- Diameter of the small base
- Diameter of the large base
- Inside material composition (air, vaccuum, ...)
- Wall thickness
An animation showing the change in each field (including Poynting field) at some well chosen time t and slice s can help visualizing the results and determine whether small changes in values greatly affect the results (or not).
Candidate shapes for further analysis
- Shell's extended frustum design with hexagonal section
Creating an animation from a set of images
An animation conveys more information and takes less space than individual images! Here is how to create a mp4 from a set of .pngs:
convert -antialias *.png emdrive.mp4
ffmpeg -framerate 10 -i emdrive%03d.png -s:v 1280x720 -c:v libx264 -profile:v high -crf 20 -pix_fmt yuv420p emdrive.mp4
Models & results
- deuteragenie toy 2D model (TBD find ctl, movie on thread 2)
- aero bradycone 3D model (TBD find refs.)
- aero nsf 3d model (TBD find refs.)
- leo? 3d model with full synchronization and updates for meep 1.3 (TBD find refs.)
Runtime & performance
TBD: Add a table with reported run times. For the moment: count on more than one hour to run the reference .ctl file on a "normal" computer.